dbx EQ 2231, Equalizer, 2 x 31 Band EQ

professioneller Equalizer für Studio- und Live-Anwendungen

Eigenschaften:
• Revolutionary instant encode/decode Type III® Noise Reduction in-circuit at the push of a button. Increases S/N ratio by up to 20dB
• Patent-pending PeakPlus™ Limiter threshold range from 0dBu to +24dBu (off) can transparently tame the wildest hits or the subtlest nuances of any signal
• Four segment LED bargraph for BOTH Gain Reduction AND Output Level
• Status LEDs offer visual feedback for all settings on the front panel

Spezifikationen:
-Input Connectors: 1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
-Input Type: Electronically balanced/unbalanced, RF filtered
-Input Impedance: Balanced 40 kOhm, unbalanced 20 kOhm
-Max Input: >+21dBu balanced or unbalanced
-CMRR: >40dB, typically >55dB at 1kHz
-Output Connectors: 1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
-Output Type: Impedance-balanced/unbalanced, RF filtered
-Output Impedance: Balanced 200 ohm, unbalanced 100 ohm
-Max Output: >+21dBu balanced/unbalanced into 2 kOhm or greater; >+18dBm balanced/unbalanced (into 600 ohm)
-Bandwidth: 20Hz to 20kHz, +/-0.5dB
-Frequency Response: 50kHz, +0.5/-3dB
-Signal-to-Noise (NR In: +/-6 and +/-15dB ranges: >102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
-Dynamic Range (NR In: +/-6dB and +/-15dB ranges): >120dB, unweighted
-Signal-to-Noise (NR Out: +/-6dB range): >94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
-Dynamic Range (NR Out: +/-6dB range): >112dB, unweighted
-Signal-to-Noise (NR Out: +/-15dB range): >90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
-Dynamic Range (NR Out: +/-15dB range): >108dB, unweighted
-THD+Noise: <0.04%, 0.02% typical at +4dBu, 1kHz
-Interchannel Crosstalk: <-80dB, 20Hz to 20kHz
-Noise Reduction: Up to 20dB of dynamic broadband noise reduction
-NR Switch: Activates dbx Type III Noise Reduction
-Bypass Switch: Bypasses the graphic equalizer section in the signal path
-Low cut Switch: (recessed) Activates the 40Hz 18dB/octave Bessel high-pass filter
-Range Switch: (recessed) Selects either +/- 6dB or +/- 15dB slider boost/cut range
-I/O Meter: 4-LED bar graph (Green, Green, Yellow, Red) at -10, 0, +10, and +18dBu
-Gain Reduction Meter: 4-LED bar graph (all Red) at 0, 3, 6, and 10dB
-Indicators: NR Active (Yellow); EQ Bypass (Red); Clip (Red); Low Cut (Red); +/-6dB (Yellow); +/-15dB (Red)
-Operating Voltage: 100VAC 50/60Hz; 120VAC 60Hz; 230VAC 50/60Hz
-Power Consumption: 28W
-Power Connector: IEC receptacle
-Dimensions: 5.25" H X 19" W X 7.9" D (13.335cm x 48.3cm x 20.1cm)